Ricoh 9100DN - Aficio SP B/W Laser Printer Provozní pokyny Strana 1

Procházejte online nebo si stáhněte Provozní pokyny pro Software Ricoh 9100DN - Aficio SP B/W Laser Printer. Ricoh 9100DN - Aficio SP B/W Laser Printer Operating instructions Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 168
  • Tabulka s obsahem
  • ŘEŠENÍ PROBLÉMŮ
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
Read this manual carefully before you use this machine and keep it handy for future reference. For safe and correct use, be sure to read the Safety Information
before using the machine.
10
8
9
Guide to the Printer
Setting Up
Connecting the Printer
Configuration
Installing the Printer Driver
Paper and Other Media
Replacing Consumables
Cleaning and Adjusting the Printer
Troubleshooting
Removing Misfed Paper
Appendix
1
2
3
4
5
6
7
11
Hardware Guide
Operating Instructions
Zobrazit stránku 0
1 2 3 4 5 6 ... 167 168

Shrnutí obsahu

Strany 1 - Hardware Guide

Read this manual carefully before you use this machine and keep it handy for future reference. For safe and correct use, be sure to read the Safety In

Strany 2

• [Booklet Finisher] Finisher SR40008

Strany 3 - TABLE OF CONTENTS

The entered number of characters for the WEP Key (ASCII entry) is incorrect.• Enter the correct WEP key.• See p.47 "IEEE 802.11b (Wireless LAN)

Strany 4 - 7. Replacing Consumables

Hardware Problem Parallel I/FThe printer identified a parallel interface error.• Turn the power switch to Standby, and then to On.• Also, check the co

Strany 5

• Prepare a new toner bottle.• You can print until [Add Toner] appears.Menu Protected Cannot changeThe operation panel has been digitally locked, and

Strany 6 - This machine has labels for

Paper is jammed in the finisher.• Open the finisher cover and remove jammed paper.• See p.137 "Remove Misfeed R: Finisher".Remove Paper ins

Strany 7

• Call your sales / service representative as soon as possible.Replace Fusing UnitIt is time to replace the Fusing Unit.• You can still print even if

Strany 8 - Manuals for This Printer

• Enter the SSID of the wireless LAN.• See p.47 "IEEE 802.11b (Wireless LAN) Configuration".Supply order failedCall for supply order has fa

Strany 9 - How to Read This Manual

When Call-light Is Lit or Blinking• Do not push or pull the call-light when installed to the printer. Doing so may result in damage ormalfunction of t

Strany 10

AQU070S1. Use the lever to adjust the volume.2. Push the lever to switch the buzzer on/off.When Call-light Is Lit or Blinking1059

Strany 11

When the Machine does Not PrintIf the printing does not start even with printing instructions, check the following.Is the power on?Check the power cor

Strany 12

Checking the port connectionWhen the printer is directly connected via computer cable and the data-in indicator does not flash or lightup, port connec

Strany 13 - 1. Guide to the Printer

Description for the Specified ModelIn this manual, the following items explain about the printer for the specified models:This explains about the 220

Strany 14 - Exterior: Rear View

Other Printing ProblemsIf the printed image is differs from the computer's instructions, check the following:Toner smears appear on the print sid

Strany 15

Areas of image are missing or blurred.• Paper is damp. Use paper that has been stored properly.• Toner is almost empty. When the "Add Toner"

Strany 16 - Control Panel

The paper size appears on the control panel and printing is not performed using PDF DirectPrint.• When using PDF Direct Print, printout requires paper

Strany 17

• Paper is damp. Use paper that has been stored properly.• Paper is too thin. Use recommended paper.• There may be a gap between the side guide and th

Strany 18 - External Options

In the printer properties dialog box, on the [Print Quality] tab, [Advanced...], [Postscript Option],[Postscript Output Option].RPCSIn the printer pro

Strany 19 - Internal Options

Additional TroubleshootingTroubles related to the printer functions.Strange noise.• If the strange noise is heard from the place where a supply has be

Strany 20

• If an Alert-notification e-mail, set with the earlier notification level, arrives, later e-mail will not be sent,even if the notification level is c

Strany 21 - 2. Setting Up

Pausing Print When Using FinisherYou can pause a large volume of prints when using Finisher.1. Press the [Suspend/Resume] key.The key lights up.ANQ082

Strany 22

Removing Jammed Staples• Keep your hands clear of the booklet finisher tray when pulling out or pushing in the finisher's stapleunit. You can tra

Strany 23 - • frequent strong vibration

4. Pull the cartridge gently out of the staple unit.AST025S5. Push the buttons on either side of the cartridge and open the plate.AST121S6. Remove the

Strany 25

AST123S8. Reinstall the cartridge, pushing it into the unit until it clicks.AST060S9. Return the staple unit to its original position.10. Close the fi

Strany 26

AST038S3. Open the face plate of the cartridge.AST039S4. Remove the jammed staples.AST040S5. Pull the face plate down until it clicks.Removing Jammed

Strany 27

AST041S6. Hold the green lever while pushing in the cartridge until it clicks.AST042SReturn the staple unit to its original position.7. Close the fini

Strany 28 - Loading Paper

3. Pull the lever S2. Pull out the cartridge gently.AST044S4. Open the face plate of the cartridge.AST045S5. Remove the jammed staples.AST046S6. Pull

Strany 29

AST047S7. Hold the green lever while pushing in the cartridge until it clicks. Return the lever S2 to itsoriginal position.AST048SReturn the staple un

Strany 30

Removing Staple Waste1. Open the finisher's front cover.AST124S2. Release the stopper from the staple waste box, and then pull it gently out.AST1

Strany 31 - Turning the Power On

Removing Punch WasteWhen the "Empty Punch Receptacle" message appears, you cannot use the Punch function.Finisher SR841The following procedu

Strany 32

Finisher SR4000The following procedure explains how to remove punch wastes from the Finisher SR4000.1. Open the finisher's front cover.AST061S2.

Strany 33

9. Troubleshooting1269

Strany 34

10. Removing Misfed PaperRemoving Misfed PaperAn error message appears if a paper misfeed occurs. The error message gives the location of the misfeed.

Strany 35 - Test Printing

1. Guide to the PrinterExterior: Front ViewAST001S1. Call- lightNotifies you of errors during printing, such as paper jam and out of paper.2. External

Strany 36

AST016S2. Push the button A and open the guide plate.AST144S3. Remove misfed paper.AST145S4. Close the guide plate, and then close the front cover.5.

Strany 37 - 3. Connecting the Printer

AST146S6. Remove misfed paper.AST147S7. Close the top cover.8. If the error message persists, open the front cover.9. Turn the lever C1 to the left.AS

Strany 38 - Reading the LED Lamps

ASU516S11. Close the front cover.• Jammed paper inside the LCT may be difficult to remove depending on the paper size set. Follow step8 to remove it.R

Strany 39 - USB Connection

ASU513S3. Return the lever B2 to its original position.ASU514SAfter removing the paper, return the lever to its original position.If you cannot remove

Strany 40 - Parallel Connection

ASU516SAfter removing the paper, return the lever to its original position.If you cannot remove the paper, proceed to the following step.6. Turn the f

Strany 41 - 4. Configuration

AST136S9. Raise the lever D4.AST137S10. Remove the paper being careful not to touch the area around the lever D4.AST138SAfter removing the paper, retu

Strany 42

AST139S12. Raise the lever E3.AST140S13. Remove the paper being careful not to touch the area around the lever E3.AST141SAfter removing the paper, ret

Strany 43 - Ethernet Configuration

AGU142S15. Remove misfed paper.AST143S16. Return each unit and lever to their original positions, and then close the front cover of themachine.Remove

Strany 44

AST148S2. Raise the feed roller.AST149S3. Remove misfed paper.AST150S4. Lower the feed roller, and then close the interposer's upper cover.5. If

Strany 45

AST151S6. Lower the lever Q1, and then remove misfed paper.AST152S7. If you cannot remove the paper, lower the Q2 lever, and then remove misfed paper.

Strany 46 - Setting the Ethernet Speed

Exterior: Rear ViewAST002S1. Ethernet PortUse a network interface cable to connect the printer to the network.2. USB portUse a USB cable to connect th

Strany 47

Finisher SR841AST023S1. Open the finisher’s front cover.AST154S2. Raise the lever R1, and remove misfed paper.AST155SAfter removing the paper, return

Strany 48

AST156SAfter removing the paper, return the lever to its original position.4. If you cannot remove the paper, raise the lever R3, and then remove misf

Strany 49

AST159SAfter removing the paper, return the lever to its original position.7. If you cannot remove the paper, raise the lever R6, and then remove misf

Strany 50

Finisher SR4000AST024S1. Open the finisher's front cover.2. Turn the blue lever R1 counterclockwise.AST026S3. Turn the blue knob R2 counterclockw

Strany 51 - Setting SSID

AST028SAfter removing the paper, return the lever to its original position.5. If you cannot remove the paper, raise the lever R3, and then remove misf

Strany 52 - Setting a WEP key

AST030SAfter removing the paper, return the lever to its original position.8. If you cannot remove the paper, lower the lever R6, and then remove misf

Strany 53

AST034S11. Pull the lever R10 and pull out the staple unit, and then remove misfed paper.AST035S12. If you cannot remove the paper, open the lever R11

Strany 54

AST037SAfter removing the paper, return the lever to its original position.Return the staple unit to its original position.14. Close the finisher&apos

Strany 55 - Quick Install

10. Removing Misfed Paper14610

Strany 56

11. AppendixMoving and Transporting the PrinterWhen you move and transport your machine, contact the store where it was purchased or where serviceis p

Strany 57

InsideAST003S1. Fusing UnitFuses the image onto paper.When "Replace Fusing Unit" message appears on the panel display, replace the fusing un

Strany 58

DisposalTo dispose of the machine, contact the store where it was purchased or where service is provided.11. Appendix14811

Strany 59

ConsumablesTo purchase the following consumables, contact your sales or service representative.Toner bottlesNumber of pages per bottleToner bottle 43,

Strany 60

SpecificationMainframeConfiguration:ConsolePrint Process:Laser beam scanning & electrophotographic printingDual component toner developmentFirst P

Strany 61 - Paper Recommendations

Monotype Imaging 35 Intellifonts, 10 TrueType fonts, and 1 bitmap fontPostScript 3:136 fonts (Type 2:24, Type 14:112)Paper SizeSee p.57 "Paper a

Strany 62 - Thick Paper

Standard paper tray 550 sheets × 2 (80 g/m2, 20 lb.)Paper weight: 60 - 105 g/m2 (16 - 28 lb.)Memory:256 MBHard Disk Drive :80 GBNetwork :Topology: Eth

Strany 63 - Print Area

• 1,500 sheets (A3 , B4 JIS , A4 , B5 JIS , 11 × 17 , 81/2 × 14 , 81/2 × 11 , 12× 18 ) (80 g/m2, 20 lb.)• 500 sheets (A5 , 51/2 × 81/2) (80 g/m2,

Strany 64 - 4. Approx. 2 mm (0.08 inches)

• 250 sheets (A4 , B5 JIS , A5 , B6 JIS , 81/2 × 11 , 51/2 × 81/2 ) (80g/m2, 20 lb.)• 50 sheets (A3 , B4 JIS , 11 × 17 , 81/2 × 14 , 12 × 18 ) (8

Strany 65

Staple position:4 position (Top, Top Slant, Bottom, 2 Staples)[Finisher Shift Tray 2]Paper size:A3 , B4 JIS , A4 , B5 JIS , A5 , B6 JIS , A6 , 11 × 17

Strany 66 - Specifying the Paper Type

• 125 sets (2 - 9 sheets) (A4 , B5 JIS , 81/2 × 11 )(80 g/m2, 20 lb.)• 125 - 40 sets (10 - 30 sheets) (other paper size)(80 g/m2, 20 lb.)• 125 sets (2

Strany 67

2 & 4 holes type2 holes A3 - A5, 11 × 17 - 51/2 × 81/22 holes A4 - A5, 81/2 × 11, 51/2 × 81/24 holes A3, B4 JIS, 11 × 174 holes A4, B5 JIS, 81

Strany 68

Control PanelAST004S1. DisplayShows the current status of the printer and error messages.2. [Job Reset] keyWhen the printer is online, press this key

Strany 69

4 holes A4, 81/2 × 114 holes type(for Northern Europe)4 holes A3 - B5 JIS, 11 × 17 - 71/4 × 101/24 holes A4 - A5, 81/2 × 11, 51/2 × 81/24 holes typ

Strany 70

52 - 128 g/m2, 14 - 34 lb.There are types of paper between 128 - 216 g/m2 in weight that are not supported.Paper capacity:4,000 sheets (80 g/m2, 20 lb

Strany 71 - Specifying Custom Size Paper

• SmartDeviceMonitor and Web Image Monitor are supported.Data Transfer Speed:Auto select from below speed1 Mbps, 2 Mbps, 5.5 Mbps, 11 MbpsAuto select

Strany 72 - Printing onto Tab Stock

2412-2462 MHz (1-11 channels)Transmittable Distance:1 Mbps 400 m2 Mbps 270 m5.5 Mbps 200 m11 Mbps 140 mThese figures are a guideline for outdoor use.

Strany 73

11. Appendix16211

Strany 74

INDEXAAddingPaper...63CChanging the Paper SizeTray 2 and 3...

Strany 75

MEMO164 G148

Strany 76

Copyright © 2006

Strany 77

G148-7202EN USAMLP175n/P7675/LP275hdn/Aficio SP 9100DNModel No.Operating Instructions Hardware Guide

Strany 78

Press this key to return to the previous condition on the display.10. [ Enter] keyPress this key to confirm or apply settings to proceed to the subse

Strany 79

OptionsThis section introduces the names and functions of main optional parts.External OptionsThis section provides explanations about external option

Strany 80

8. InterposerInserts cover or slip sheets into the printed.9. A3/11" × 17" tray unitYou can load A3 or 11" × 17" paper in tray

Strany 81 - 5. Remove the outer cap

TrademarksMicrosoft, Windows and Windows NT are registered trademarks of Microsoft Corporation in the United States and/or other countries.Adobe®, Pos

Strany 82

1. Guide to the Printer181

Strany 83 - Adding Staples

2. Setting UpWhere to Put the Printer• Confirm the wall outlet is near the machine and freely accessible, so that in the event of emergency,it can be

Strany 84 - 4. Raise the cover

A: 10 cm (4 inches) or moreB: 5 cm (2 inches) or moreC: 4 cm (1.6 inches) or moreD: 70 cm (27.6 inches) or more• Permissible and recommended temperatu

Strany 85

• frequent strong vibration• EMF from nearby electronic equipmentWhere to Put the Printer212

Strany 86

Installing the Toner bottle• Do not incinerate used toner or toner containers. Toner dust might ignite when exposed to an openflame. Dispose of used t

Strany 87 - 7. Pull out the ribbon

2. Take the new toner bottle from the box.AST103S3. Hold the bottle horizontally, and then shake it five or six times without removing the outercap.AS

Strany 88

AST106S6. Insert the toner bottle. Push it in until the green lever clicks.AST107S7. Return the lever under the toner bottle to its original position.

Strany 89

• Toner bottles are not covered by warranty. However, if there is problem, contact the store where theywere purchased.• If the toner bottle does not c

Strany 90 - 8. Pull out the ribbon

Loading PaperLoading paper into the paper trays.Loading Paper into Tray 1 (Tandem Tray)The following procedure explains loading paper into Tray 1.The

Strany 91

ANS052S• Left half of the tray pulled outANS053S3. Carefully push the paper tray fully in.• You can load paper even while printing from Tray 1. You ca

Strany 92

TABLE OF CONTENTSPositions of WARNING and CAUTION labels...

Strany 93

ANS054S2. Square the paper, and then load it print side down.ANS055S3. Carefully push the paper tray fully in.• The tray can hold up to 550 sheets.2.

Strany 94 - Adjusting Tray Registration

Turning the Power On• Plug and unplug the power cable with dry hands, or an electric shock could occur.Power Switch• Power Switch (front left)Setting

Strany 95

• This machine automatically enters the Energy Saver mode if you do not use it for a certain period.2. Setting Up302

Strany 96

Selecting the Display LanguageThe following explains the procedure for selecting a language on the display.A message about selecting the language will

Strany 97

5. Press the [ Enter] key.Wait for two seconds. The [Menu] screen appears.6. Press the [Online] key.AST010SThe initial screen appears.• The default s

Strany 98

Test PrintingThe following explains the procedure for test printing of the configuration page.1. Press the [Menu] key.AST008SThe menu appears on the d

Strany 99

AST010SThe initial screen appears.• Make a test print to confirm the printer is working normally. Test printing checks printer performanceonly; it doe

Strany 100 - 9. Troubleshooting

3. Connecting the PrinterNetwork ConnectionThe following explains the procedure for connecting the printer to the computer through the network.Prepare

Strany 101

• The printer's ethernet and USB ports are not available when the gigabit ethernet board is attached tothe printer.• For details about network en

Strany 102

USB Connection• The USB2.0 cable is not supplied. Obtain a cable that is suitable for the computer you are using.• USB connection is possible under Wi

Strany 103

Setting the Ethernet Speed...44

Strany 104

Parallel Connection• The parallel interface cable is not supplied with the printer.• The printer's parallel connection is a standard bidirectiona

Strany 105

4. ConfigurationEthernet ConfigurationMake the following network settings according to the network interface you are using. You can use Smart-DeviceMo

Strany 106

AST008SThe menu appears on the display.2. Press the [ ] or [ ] key to select [Host Interface], and then press the [ Enter] key.3. Press the [ ] or [

Strany 107

8. If you use IPv4, assign the IPv4 address to the printer. Press the [ ] or [ ] key to select [IPv4Settings], and then press the [ Enter] key.To get

Strany 108

AST008SThe menu appears on the display.2. Press the [ ] or [ ] key to select [Host Interface], and then press the [ Enter] key.3. Press the [ ] or [

Strany 109 - Checking the port connection

• For details about printing the configuration page, see p.33 "Test Printing".Making Network Settings for Using NetwareIf you use NetWare,

Strany 110 - Other Printing Problems

4. Press the [ ] or [ ] key to select [Frame Type (NW)], and then press the [ Enter] key.5. Press the [ ] or [ ] key to select the frame type, and th

Strany 111

Router/HUBPrinter[10Mbps HalfD.][10Mbps FullD.][100MbpsHalf D.][100Mbps FullD.][Auto Select]auto-negotia-tion (auto se-lection)- -• Connection cannot

Strany 112

5. Press the [ ] or [ ] key to select the ethernet speed, and then press the [ Enter] key.6. Press the [Menu] key to return to the initial screen.7.

Strany 113

IEEE 802.11b (Wireless LAN) ConfigurationConfigure the printer to use IEEE 802.11b (Wireless LAN). The following table shows the control panelsettings

Strany 114

When the Machine does Not Print...106Check

Strany 115 - Additional Troubleshooting

2. Press the [ ] or [ ] key to select [Host Interface], and then press the [ Enter] key.3. Press the [ ] or [ ] key to select [IEEE 802.11b], and the

Strany 116

The factory default is [Auto]. If you need to change the transmitting speed depending on environmentyou are using, select the appropriate transmitting

Strany 117

Setting a WEP keyIn the case of using a WEP key on a network, activate the WEP setting to be used for communication alongwith WEP.Consult your network

Strany 118 - Removing Jammed Staples

• WEP key can also be set using a Web browser. For details, see Web Image Monitor Help.• For details about printing the configuration page, see p.33

Strany 120 - Finisher SR4000

5. Installing the Printer DriverQuick InstallWindows 95/98/Me/2000/XP, and Windows Server 2003 users can easily install this software usingthe CD-ROM

Strany 121 - 4. Remove the jammed staples

7. Click [Install].The printer driver installation starts.8. Click [Finish].A message about restarting the computer appears. Restart the computer to c

Strany 122

Install the Operating InstructionsThe CD-ROM provided with the printer contains an HTML Operating Instructions Manual. Follow theprocedure below to in

Strany 123 - 5. Remove the jammed staples

5. Installing the Printer Driver565

Strany 124

6. Paper and Other MediaPaper and Other Media Supported by This Print-erThis section describes the paper size, feed direction, and the maximum amount

Strany 125 - Removing Staple Waste

Positions of WARNING and CAUTION labelsThis machine has labels for WARNING and CAUTION at the positions shown below. For safety,please follow the ins

Strany 126 - Removing Punch Waste

Metric version Inch versionA3 , B4 JIS , A4 , B5 JIS , A5 , 11× 17 , 81/2 × 14 (Legal) , 81/2 × 11 (Letter), 51/2 × 81/2, 71/4 × 101/2 (Execu-tive) ,

Strany 127

Paper RecommendationsLoading Paper• Do not use ink-jet printer paper because it may stick to the fusing unit and cause a paper misfeed.• When printing

Strany 128

• The paper size settings made using the controlpanel have priority over the printer driver set-tings.Printer driver setupSelect [Plain] or [Plain/Rec

Strany 129 - 10. Removing Misfed Paper

Both-side printing PossibleAdditional cautions• Print speed is slightly slower than when usingplain paper.• There are types of paper between 128 - 216

Strany 130 - 5. Open the top cover

1. Print area2. Feed direction3. Approx. 4 mm (0.16 inches)4. Approx. 2 mm (0.08 inches)• The print area may vary depending on the paper size, printer

Strany 131 - Removing Misfed Paper

Loading PaperThe following section explains how to load paper when paper runs out.• When loading paper, take care not to trap or injure your fingers.L

Strany 132 - Remove Misfeed B-F: Internal

Whole tray pulled outANS052SLeft half of the tray pulled outANS053S3. Carefully push the paper tray fully in.• You can load paper even while printing

Strany 133

AST008SThe menu appears on the display.2. Press the [ ] or [ ] key to display [Paper Input], and then press the [ Enter] key.The paper type selection

Strany 134

• The setting made here is valid until the next setting is made. After printing on thick paper, reset it tothe original setting for the next user.• Fo

Strany 135

Changing the Paper Size in Tray 2 and 3The following explains the procedure for changing a paper size in Tray2 and 3.• If a paper tray is pushed vigor

Strany 136

AST007S1. The inside of this printer becomes very hot. Do not touch parts with this label (indicating a hot surface).Touching these parts will result

Strany 137 - Remove Misfeed Q: Interposer

ANS024S5. Slide the end fence until it is aligned with the paper size you want to load.ANS025S6. Square the paper and load it print side up.Re-lock th

Strany 138 - 2. Raise the feed roller

Specifying Custom Size PaperWhen printing on custom size paper, specify the paper size using the control panel or printer driver.The following is the

Strany 139 - Remove Misfeed R: Finisher

The screen for entering the length appears.7. Press the [ ] or [ ] key to set the vertical value, and then press the [ Enter] key.By pressing the key

Strany 140 - Finisher SR841

1. Select the paper tray where the tab stock is set.AST014S2. Set tab stock so that it will be fed from the side without the tab first.3. Adjust the b

Strany 141

6. Press the [ ] or [ ] key to display [Paper Input], and then press the [ Enter] key.7. Press the [ ] or [ ] key to display [Tray 2] or [Tray 3], an

Strany 142

ANQ009S3. Carefully slide the paper tray fully in.• The tray can hold up to 550 sheets.Loading Paper into the Large Capacity Tray (LCT)The following p

Strany 143

AST110S3. Press the [Down] key.The key blinks while the bottom plate is moving down.AST111S4. Load paper by repeating steps 2 and 3.The tray can hold

Strany 144

• Do not stack paper higher than the limit mark inside the tray.1. Load the paper.AST112S2. Adjust the paper guides to the paper size.AST113S• Straigh

Strany 145

6. Paper and Other Media766

Strany 146

7. Replacing ConsumablesReplacing the Toner bottle• Do not incinerate used toner or toner containers. Toner dust might ignite when exposed to an openf

Strany 147

Manuals for This PrinterFor particular functions, see the relevant parts of the manual.Safety InformationProvides information on safe usage of this ma

Strany 148

1. Open the front cover of the machine.AST016S2. Pull out the lever under the toner bottle toward you, until it is at 90°.AST163S3. Raise the green le

Strany 149 - 11. Appendix

AST104S5. Remove the outer cap.AST105S6. Place the toner bottle in position, and then push it in until the green lever clicks.AST107S7. Return the lev

Strany 150 - Disposal

AST108S8. Close the front cover of the machine.7. Replacing Consumables807

Strany 151 - Consumables

Adding Staples• Keep your hands clear of the booklet finisher tray when pulling out or pushing in the finisher's stapleunit. You can trap your fi

Strany 152 - Specification

AST025S4. Raise the cover.AST116S5. Insert the new refill, and then lower the cover until it clicks.AST117S7. Replacing Consumables827

Strany 153

AST118S6. Pull out the ribbon.AST119S7. Reinstall the cartridge, pushing it into the unit until it clicks.AST060S8. Reinstall the staple unit.9. Close

Strany 154

2. Pull out the staple unit. Pull out the cartridge gently.AST038S3. Hold both sides of the cartridge, and then pull up the upper unit of it.AST049S4.

Strany 155

AST051S6. Gently push down the upper unit into the cartridge.AST052S7. Pull out the ribbon.AST053S8. Hold the green lever while pushing in the cartrid

Strany 156

AST042SReturn the staple unit to its original position.9. Close the finisher's front cover.• If you cannot pull out the upper unit, there are sta

Strany 157

AST044S4. Hold both sides of the cartridge, and then pull up the upper unit of it.AST054S5. Take out the empty refill in the arrow direction.AST055S6.

Strany 158 - Punch Unit (Finisher SR4000)

How to Read This ManualSymbolsThe following set of symbols is used in this manual.This symbol indicates a potentially hazardous situation that might r

Strany 159 - Punch Unit (Finisher SR841)

AST056S7. Gently push down the upper unit into the cartridge.AST057S8. Pull out the ribbon.AST058S9. Hold the green lever while pushing in the cartrid

Strany 160 - Large Capacity Tray RT43

AST048SReturn the staple unit to its original position.10. Close the finisher's front cover.• If you cannot pull out the upper unit, there are st

Strany 161 - Cover Interposer Type 3260

7. Replacing Consumables907

Strany 162

8. Cleaning and Adjusting the PrinterCautions to Take When Cleaning• Do not remove any covers or screws other than those specified in this manual. Som

Strany 163 - Gigabit Ethernet Board Type A

Adjusting Tray RegistrationYou can adjust the registration of each tray. Vertical adjustment is used for all trays. Normally, you neednot update the r

Strany 164

6. Press the [Escape] key.7. Press the [ ] or [ ] key to display [Adjustment], and then press the [ Enter] key.8. Press the [ ] or [ ] key to display

Strany 165

AAL708S(1): Print Area(2): Feed DirectionPressing the [ ] or [ ] key makes the value increase or decrease by 1.0 mm steps.10. Press the [ Enter] key.

Strany 166

9. TroubleshootingError & Status Messages on the Display PanelThis section describes the main messages that appear on the panel display. If a mess

Strany 167 - Copyright © 2006

The printer is out of the staple.• Add staples, cancel staples mode or cancel the job.• See p.81 .Add staples (Booklet)Both staplers of the Booklet Fi

Strany 168 - Model No

• Cancel duplex mode. Alternatively, select another tray using [Form Feed], or cancel the job.Cannot select same Tray for: / Main sheet and Designate:

Komentáře k této Příručce

Žádné komentáře